2 Pkg Underground Wire Splice Kit UF Splice Kit 8/3 to 2/3 Range Direct Buried UF Wire Splice Connectors Extension Cord Splice Kit 8-2 AWG Screw Splice Connectors with 8 inch. Heavy-Wall Heat Shrink

MAVooPoo UF Splice Kit Specification:MAVooPoo Splice Kit UF is designed to provide a reliable, moisture proof electrical connection for type UF-B underground feeder cable rated for 600 V (copper wire only) ranging.The applicable range of this standard UF Splice Kit covers Type UF-B cables from #14/3 (without a ground wire) up to #8/3 (with a ground wire).For the large-sized version of the UF Splice Kit, it is compatible with cables in the wire gauge range of minimum AWG 8 to maximum AWG 2.MAVooPoo UF Splice Kit is offered in two versions: Standard Kit includes a 1.8” length terminal connector; 8” length of heavy wall, adhesive lined heat shrinks tube. Stretcher Kit offers a 11.5” length terminal connector; 20” length of heavy wall, adhesive lined heat shrink tube.UNDERGROUND FEEDER CABLE SPLICE KIT, 8-2 AWG COMPLETE KIT: This UF splice kit consists of a connector-insulation assembly and a heat shrink tube. The connector assembly contains four cylindrical set screw connectors separated by a piece of Polycarbonate insulation. The heat shrink tube is a heavy-wall, adhesive-lined tube. Underground Feeder (UF)-B cables are flat, and typically have three solid conductors without a ground or two solid conductors with a ground. They range in size from 8-2AWG.Repair of underground feeder UF-B cables rated for 600 volts, ranging from size #8/3 with ground wire up to #2/3 with ground wire. In cases of dig-in repair or extensions, the MAVooPoo UF Splice Kit, Standard versions, will produce a connection that is insulated and moisture resistant. Application Temperature 0°F to 120°F(-18°C to 49°C).Operation Temperature -67°F to 230°F(-55°C to 110°C).TO COMPLETE A SPLICE OF #8 TO #2 GAUGE UF COPPER WIRE, FOLLOW STEPS 1 THROUGH 9:WARNING!: Turn power off before installing or removing terminal or connector.All work should be done according to appropriate electrical codes.1. Remove 2” of jacket from UF cable. 2. Strip 5/8” of insulation from conductors. 3. Clean cable surface and wipe dry, approximately 4 inches per side of the splice. Lightly abrade the two clean insulation surfaces. Clean cable surface and wipe dry again. 4. Slide the enclosed long piece of heat shrink tube over one end of the wire. 5. Insert wires, one at a time, into the brass connector making sure that the wires of desired connection are in the same brass sleeve. Make sure that the wires are inserted an equal length into the brass sleeve so that the set screw can engage into the copper of each wire. 6. Tighten screws with 8 inch pounds of torque. 7. Slide long piece of heat shrink over connection centering it with respect to the brass/plastic connector assembly. 8. Apply heat to the shrink tube with a torch or heat gun starting in the middle of the shrink tube, moving out to each end. Properly installed, shrink tube will be smooth and conform to the cable. Adhesive should be visible at each end of the shrink tubing.9. Apply heat to tube until adhesive flows out on both ends of tube.

• PACKAGE CONTENTS: 14-8 AWG Underground Cable Splice Kit Includes: 8 inch. Heavy-Wall Heat Shrink & Screw Splice Connectors
• HIGH QUALITY MATERIAL: Our Wire Connectors which are made of high quality brass to provide premium electrical and mechanical performance. Although its electrical conductivity is not as good as that of pure copper, compared with some other metals, it still has excellent heat and electrical conductivity, high malleability, resistance to corrosion.
• EXCELLENT CONDUCTIVITY: Each Brass Wire Butt Connectors has a Thick, Seamless, one piece pure brass tubular construction. it has good electrical conductivity and can meet the needs of most general electrical connections. Brass Butt Splice Connectors provide the best performing electrical connection between your power sources and your power cable.
• EASY INSTALLATION PROCESS: The process of using screw wire connectors for wire connection is relatively intuitive and straightforward. No special tools are required, nor are complicated professional skills, which reduces the difficulty of electrical wiring. Screws are tightened until full connection of conductors. Simple screw-on design for quick and hassle-free installation.
• INSPECTION WINDOW: Our screw wire butt connectors have an inspection hole in the center for monitoring full cable insertion, also provides a solder place for tin and wire. Additional soldering through the control hole in the middle is recommened.